Audra Haynes Lamp Shades September 01st, 2018 - 02:22:04
This lampshade around the top to kind of keep the bright bulb from being visible, but that works pretty good and I've used This for quite a number of years. I think I converted that maybe 10 years ago and this is the second generation conversion that I did I just took out the bulb and screwed in an LED bulb Edison base because of the bulbs a little bit taller. I had to put a taller lampshade around the top, but that lamp has been working fine for three or four years now.
I think, since I converted it and all I had to do to make this conversion was just swapped the for an LED bulb and the reason I went to the LED was you could get different wattage different color temperatures, mandible non-mandible different color, rendering index is you could have a lot of choices there, while the bulbs, you are pretty much limited and definitely not mandible yeah, so this is the bulb again, I have it off all these floors. Lamps. I have have a two-position switch. You can see.
That's the dim setting and it gives one flash and that's it, and then you have full brightness. So with these lamps, I was not able to get any dimming. The only way to change the brightness was to change bulbs. So I have the 58 watt, which was probably a little too bright, and then I went down to this forty watt unit, which is okay, but it's not mandible, and also this one. You cannot control with a remote outlet, so I have some either z-wave or I used to have the x10 remote control outlets and you cannot use those with a bulb. They just do not work. The bulb will just sit there and flash like it did with the dimmer and it'll just flash on and off every couple of seconds with the switch off. If you turn it on it works. Okay, you just can't turn it off. It'll just sit there.
There's enough trickle current that just causes the to flicker on and off. So let me show you my third-generation conversion. Okay, this is my third generation lamp conversion and there we go. This is about a four-watt setting and then I can turn the dimmer and that's 20 watts. Now, one problem: you might notice right here these lamps, that I have had kind of translucent green base and they rely on some of the light leaking out of the bulb to kind of give this a soft glow. So right now that doesn't work. But if I do a little modification here there we go so I just had a piece of paper blocking some holes there in the bottom.
That is my third generation torch, a floor, lamp conversion and you can see there's no lampshade on the top and in fact, I can put my hand up there. It's not hot, and then I've got the dimmer and this one dims from 4 watts. All the way up to 20 watts and I've got the kind of the lighting down below, and I think this is about a 3,000 Kelvin there are various color temperatures available, wattage mandible non-mandible. So let me show you how I did this. In fact, what we can do is I'll take you up above, and we can take a look at that, so you can see right.
There is my lamp, so that's the lamp. This is a recessed ceiling, lamp around fixture and it just sits right down in there just like the old halogen bulb did, but you don't burn yourself on it. It's cool to the touch and that's 4 watt, and if you go up here, that's about 20 watts and that's plenty of light for this room here you know a 300 watt halogen bulb would be much brighter than this. I imagine this. This is probably brighter than a 75 watt bulb, maybe about as bright as a hundred and fifty watt halogen bulb, but only 20 watts of power consumption, and you can see it. It turns off at dims it brightens. You got the translucent down lighting.
Copyright © 2019 corpfinblog.com. Reproduction without explicit permission is prohibited. All Rights Reserved.
User Agreement, Privacy, Cookies. Buffet Lamps floor lamps 8 inch wall clock white bathroom vanity led string lights plastic soap dispenser best toilet seat oak rocking chair round tablecloth bathroom sinks plastic tablecloth outdoor light best accent chair.